MIAO Chengliang SHANG Chengjia WANG Xuemin ZHANG Longfei Mani Subramanian. MICROSTRUCTURE AND TOUGHNESS OF HAZ IN X80 PIPELINE STEEL WITH HIGH Nb CONTENT. Acta Metall Sin, 2010, 46(5): 541-546.
- Abstract
- References
- Related Articles
- Recommended
- Metrics
| Download: | |
| Abstract High Nb-bearing X80 pipeline steel has low cost and excellent combined properties. However, welding will worsen its microstructure and toughness. In this paper, X80 pipeline steel with 0.1%Nb (mass fraction) was chosen, and single welding thermal-cycles with different heat inputs (16, 20, 30, 40, 50, 58 kJ/cm) were simulated by Gleeble-1500 to study the correlation of toughness and microstructure in heat affect zone (HAZ) of actual welding pipe. The evolution characteristics of microstructure of the coarse grain zone in welding heat affect zone (CGHAZ) were investigated by OM, SEM and EBSD. The results indicated heat input in single welding should be less than 30 kJ/cm to ensure good Charpy impact toughness. Although the strong dragging effect of solute Nb can suppress serious coarsening of average grain size in high Nb steel, the uniformity of prior austenite grains is worsened as increasing the heat input. Moreover, the characteristics of high angle boundaries (HABs) and M/A constituents also are influenced by heat input. In the case of low heat put, higher density of HABs, disperse and fine M/A constiuents were observed, and HABs can form at two sites, one is prior austenite grain boundary, the other is between the lower bainites belong to different Bain groups in the same austenite grain. Otherwise, in the case of high heat input (≥40 kJ/cm), the misorientation between granular bainites in idential austenite grain is small, i.e., the effective grain size is almost the diameter of prior austenite grain, and it will decrease the density of high angle boundary largely, moreover, coarse M/A constituents which are benefit for crack initiation will be generated, consequently, the impact toughness of the coarse grain zone will be worsened obviously in welding heat affect zone. | |
| Received: 01 December 2009 | |
| Fund: Supported by National Natural Science Foundation of China (No.50734004) | |
| Service | |
 | Add to citation manager |
| E-mail Alert |
| RSS |
| （） |
| Articles by authors | |
| MU Cheng-Liang |
| CHANG Cheng-Jia |
| YU Hua-Min |
| ZHANG Long-Fei |
| |
URL:
https://www.ams.org.cn/EN/10.3724/SP.J.1037.2009.00803OR https://www.ams.org.cn/EN/Y2010/V46/I5/541
[1] Feng Y R, Li H L. Pet Plan Eng, 2005; 9: 1
(冯耀荣, 李鹤林. 石油规划设计, 2005; 9: 1)
[2] Zheng L, Fu J Y. Iron Steel, 2006; 41(10): 1
(郑磊, 付俊岩. 钢铁, 2006; 41(10): 1)
[3] Miao C L, Shang C J, Cao J P, Wang X M, He X L. Iron Steel, 2009; 44(3): 62
(缪成亮, 尚成嘉, 曹建平, 王学敏, 贺信莱. 钢铁, 2009; 44(3): 62)
[4] Lee S, Kim B C, Lee D Y. Scr Metall, 1989; 23: 995
[5] Hwang B, Kim Y G, Lee S, Kim Y M, Kim N J, Yoo J Y. Metall Mater Trans, 2005; 36A: 2107
[6] Ohom*ori Y, Ohtani H, Kunitake T. Metall Sci, 1974; 8: 357
[7] Naylor J P, Krahe P R. Metall Trans, 1974; 5: 1699
[8] Lambert A, Garat X, Sturel T, Gourgues A F, Gingell A. Scr Mater, 2000; 43: 161
[9] Zhong Y, Xiao F R, Zhang J W, Shan Y Y, Wang W, Yang K. Acta Mater, 2006; 54: 435
[10] Chen C X, Li W S, Wang Q P, Feng B, Liu F M, Xue Z K. J Mater Eng, 2005; 5: 22
(陈翠欣, 李午申, 王庆鹏, 冯斌, 刘方明, 薛振奎. 材料工程, 2005; 5: 22)
[11] Li Y, Crowther D N, Green M J W, Mitchell P S, Baker T N. ISIJ Int, 2001; 41: 46
[12] Zurob H S, Zhu G, Subramanian S V, Purdy G R, Hutchinson C R, Brechet Y. ISIJ Int, 2005; 45: 713
[13] Zhao M C, Shan Y Y, Xiao F R, Li Y H, Yang K. Mater Sci Technol, 2001; 9: 356
(赵明纯, 单以银, 肖福仁, 李玉海, 杨柯. 材料科学与工艺, 2001; 9: 356)
[14] Diazfuentes M, Izamendia A, Gutierrez I. Metall Mater Trans, 2003; 34A: 2005
[15] Guo Z, Lee C S, Morris JW. Acta Mater, 2004; 52: 5511
[16] Morris J W, Lee C S, Guo Z. ISIJ Int, 2003; 43: 410
[17] Tomio Y, Furuhara T, Maki T. Mater Trans, 2009; 50: 2731
[18] Furuhara T, Takayama N, Miyamoto G. Mater Sci Forum, 2010; 638–642: 3044
[19] Koo J Y, Luton M J, Bangaru N V, Petkovic R A. Int J Offshore Polar Eng, 2004; 14: 75
[20] Li W W, Liu Y X, Gao H L, Zhao X W, Feng Y R, Ji L K. Trans China Weld Inst, 2006; 27: 43
(李为卫, 刘亚旭, 高惠临, 赵新伟, 冯耀荣, 吉玲康. 焊接学报, 2006; 27: 43)
| [1] | HOU Xuru, ZHAO Lin, REN Shubin, PENG Yun, MA Chengyong, TIAN Zhiling. Effect of Heat Input on Microstructure and Mechanical Properties of Marine High Strength Steel Fabricated by Wire Arc Additive Manufacturing[J]. 金属学报, 2023, 59(10): 1311-1323. |
| [2] | ZHU Dongming, HE Jiangli, SHI Genhao, WANG Qingfeng. Effect of Welding Heat Input on Microstructure and Impact Toughness of the Simulated CGHAZ in Q500qE Steel[J]. 金属学报, 2022, 58(12): 1581-1588. |
| [3] | WANG Cong, ZHANG Jin. Fine-Tuning Weld Metal Compositions via Flux Optimization in Submerged Arc Welding: An Overview[J]. 金属学报, 2021, 57(9): 1126-1140. |
| [4] | JIANG Zhonghua, DU Junyi, WANG Pei, ZHENG Jianneng, LI Dianzhong, LI Yiyi. Mechanism of Improving the Impact Toughness of SA508-3 Steel Used for Nuclear Power by Pre-Transformation of M-A Islands[J]. 金属学报, 2021, 57(7): 891-902. |
| [5] | WAN Xiangliang, HU Feng, CHENG Lin, HUANG Gang, ZHANG Guohong, WU Kaiming. Influence of Two-Step Bainite Transformation on Toughness in Medium-Carbon Micro/Nano-Structured Steel[J]. 金属学报, 2019, 55(12): 1503-1511. |
| [6] | SHAO Yi , LI Yanmo , LIU Chenxi , YAN Zesheng , LIU Yongchang . Annealing Process Optimization of High Frequency Longitudinal Resistance Welded Low-CarbonFerritic Stainless Steel Pipe[J]. 金属学报, 2019, 55(11): 1367-1378. |
| [7] | Mingyue WEN, Wenchao DONG, Huiyong PANG, Shanping LU. Microstructure and Impact Toughness of Welding Heat-Affected Zones of a Fe-Cr-Ni-Mo High Strength Steel[J]. 金属学报, 2018, 54(4): 501-511. |
| [8] | Yubin DU, Xiaofeng HU, Haichang JIANG, Desheng YAN, Lijian RONG. Effect of Tempering Time on Carbide Evolution and Mechanical Properties in a Fe-Cr-Ni-Mo High-Strength Steel[J]. 金属学报, 2018, 54(1): 11-20. |
| [9] | Zongyuan ZOU, Xiaokui XU, Yinxiao LI, Chao WANG. Study on the Method of Improving the Toughness of CGHAZ for High Heat Input Welding Steels[J]. 金属学报, 2017, 53(8): 957-967. |
| [10] | Zhiqiang SHU,Pengbin YUAN,Zhiying OUYANG,Danmei GONG,Xueming BAI. Effects of Tempering Temperature on Microstructure and Mechanical Properties of Drill Pipe Steel 26CrMo[J]. 金属学报, 2017, 53(6): 669-676. |
| [11] | Long HUANG,Xiangtao DENG,Jia LIU,Zhaodong WANG. Relationship Between Retained Austenite Stability and Cryogenic Impact Toughness in 0.12C-3.0Mn Low Carbon Medium Manganese Steel[J]. 金属学报, 2017, 53(3): 316-324. |
| [12] | Xueda LI,Chengjia SHANG,Changchai HAN,Yuran FAN,Jianbo SUN. INFLUENCE OF NECKLACE-TYPE M-A CONSTITU-ENT ON IMPACT TOUGHNESS AND FRACTUREMECHANISM IN THE HEAT AFFECTED ZONE OF X100 PIPELINE STEEL[J]. 金属学报, 2016, 52(9): 1025-1035. |
| [13] | Fengyu SONG,Yanmei LI,Ping WANG,f*ckian ZHU. EFFECTS OF HEAT INPUT ON THE MICROSTRUC-TURE AND IMPACT TOUGHNESS OF WELD METAL PROCESSED BY A NEW FLUXNOVEL FLUX CORED WIRE WELD[J]. 金属学报, 2016, 52(7): 890-896. |
| [14] | Xuelin WANG,Liming DONG,Weiwei YANG,Yu ZHANG,Xuemin WANG,Chengjia SHANG. EFFECT OF Mn, Ni, Mo PROPORTION ON MICRO-STRUCTURE AND MECHANICAL PROPERTIESOF WELD METAL OF K65 PIPELINE STEEL[J]. 金属学报, 2016, 52(6): 649-660. |
| [15] | Zhonghua JIANG,Pei WANG,Dianzhong LI,Yiyi LI. EFFECTS OF TEMPERING TEMPERATURE ON THE MICROSTRUCTURE AND MECHANICAL PROPERTIES OF GRANULAR BAINITE IN 2.25Cr-1Mo-0.25V STEEL[J]. 金属学报, 2015, 51(8): 925-934. |
No Suggested Reading articles found!
| Viewed | ||||
| Full text | | |||
| Abstract | ||||
Cited | ||||
| Shared | ||||
| Discussed | ||||
